Careful liquidation and cleaning to ensure that the parts of the computer car are clean is the foundation for ensuring the quality of the device and extending the application life of the computer car. The incorrect mutual status between parts and institutions also affects the functioning of best embroidery machines the computer car. When it is heavy, the wear will be accelerated due to debris, showing major problems such as 'occlusion', affecting the entire machine function.

Computer cars with poor device quality have low precision, poor performance, loud sound, heavy torque, and short life span; the same, for some parts with low precision, even with careful selection of devices and accurate adjustments, they can still The device produces better equipment. In addition, the shaft sleeves, bearings, oil pumps, and complete machines containing common parts of migration, transformation and swing should be carefully cleaned up.

For all computer car parts that have been treated with external baking paint, electroplating, etc. 1. there is an adhesive layer on the device joint surface (including holes, grooves, three-dimensional and screw holes), so the The parts must be finished according to the technical requirements, and then stop assembly and distribution;

If an inappropriate needle is selected, it will cause thread or needle breakage, which is very effective for embroidery factories. Introspect the depth of the knife, the knife is too shallow to cut the thread; Change the parameters of the computerized embroidery machine, and examine whether the line-dividing angle is between 310-315; In addition, there are some special reasons that can cause disconnection, even room temperature. If the thread path is tight, the tension of the thread take-up spring will shorten the upper thread.

The suitable tension of the bottom thread is: After the thread buckle fork is buckled, the bottom thread can be pulled by hand; Adjust the parameters, the opening angle, the larger the closing angle, the longer the face line. In addition, you can also take a test to tighten the cloth embroidery thread and realign the hook. Conditioned by the following methods: Introspect the thread, do not over tighten the thread take-up spring and knob; Adjust the height of the thread buckle, higher profile will make China Multifunction Mixed Embroidery Machine Manufacturers the upper thread longer, this thought is often useful in practical training Adjust the parameters, the opening angle, the larger the closing angle, the longer the face line.

As long as the thoughts on troubleshooting are targeted at the above: Sometimes when the weather is overheated, the needle is locked during the thread trimming operation, and cannot move upward. The solenoid valve that locks the needle continues to move twice, causing helplessness to cut the upper thread. There are two main types of short thread trimming results for computerized embroidery machines: short thread trimming upper thread and short thread trimming bottom thread.

In short, the main reasons for cutting the thread are the machine and the electronic control. At first, we should test some customary investigation plans, such as introspecting whether the reaming shears can achieve results, whether the reaming shears status can achieve results, whether the thread deduction can achieve results, whether the hook knife can achieve results, etc. Embroidery is a sticking point for embroidery

Therefore, when selecting the spindle motor type (such as servo, slip, variable frequency motor), the output power of the motor, and the transmission inertia of the motor, the user is required to fully analyze the transmission characteristics of the spindle system, and estimate the transmission inertia of the spindle drive system and the maximum load When there is a certain amount of torque, select a suitable spindle motor. Computerized embroidery spindle mechanical system and spindle drive motor The transmission load of the spindle mechanical system must match the output power of the spindle drive motor.

On the contrary, if the driving force of the stepper motor is lacking, it will cause problems such as pattern shifting, motor overheating, increased noise, and a one-level reduction in lifespan. For the color change of the communication motor, the communication motor of different power and different output torque (different transmission ratio) should be selected according to the number of heads of the whole machine and the number of needles of the needle bar box.

The goals of the motor are far greater than the needs of the embroidery frame it drives, which will cause waste and unnecessary increase in volume. Therefore, when selecting the stepping motor that drives the embroidery frame, the user should select a suitable motor according to the size, weight, and characteristics of the transmission organization of the embroidery frame. For the models that generally use stepping color change for 1-2 heads, generally due to the limitation of the installation position, 42 hybrid stepping motors are used, which puts high requirements on the mechanical transmission, and the load should not be too heavy, otherwise the Can not work normally.

The output power of the spindle motor is less than the spindle transmission load, which will directly affect the parking accuracy, working stability and embroidery function of the whole machine. Computerized embroidery machine embroidery frame and stepping motor driven The component and inertia of the embroidery frame must match the output torque and torque frequency characteristics of the stepping motor.

So how to improve the pleated filter media of the crimping machine Multifunction Mixed Embroidery Machine and crimping machine? Let's look down. The above teaching is to improve the method of pleating filter media of crimping machine and crimping machine.

I hope it can help everyone. Ways to improve the pleating filter media of crimping machine and crimping machine: The demand for improving discount machine technology to adapt to market trends has become increasingly obvious . Due to the lack of adjustments to the inclination angle and blade squeezing conditions of the old-fashioned crimping machine and crimping machine, the operator should pay attention to the new materials and the height of the pleats.

The partitions are often used on the blades to increase the position between the blades by mechanical methods, such as crimping machines and crimping machines with a working width of 13m or more, but the distance is the friction problem, because the partitions There is also additional friction before changing the position of the blade to match the height of the new pleats, and a large number of nuts must be removed and re-fixed.

With the above work, it will be necessary to repeat at least two requirements to adjust crimping machine and crimping machine to adapt to the increasing number of highly sensitive media in the market in recent years

The breaking law is OK.For example, the same M3 cam, the original factory costs more than 80, and in some places it only costs more than 10 yuan, or even 7. To Whether the machine is easy to use or not, the key lies in the master's debugging techniques and the quality of the accessories. M3. M8 nylon cams.

M5, M8 are more suitable for thinner fabrics, such as yarn fabrics. In fact, there is nothing, 01, M1, M3 these cams are roughly the same, they are all designed for normal high speed embroidery machine price to medium-thick fabric trajectories, and the performance is similar.

Some time ago I saw someone on the Internet asking about the use of 01. M5.M1. , You can buy it for 8 yuan, and you are afraid that you get what you pay for, and the cam is not a fragile accessory like other accessories